Bộ Vòi Phun Mk8 Cho Máy In 3d Cr-10 Cr-10S S4 S5
0 Đánh Giá
0 Đã Bán
38
184.000 đ
Xem sản phẩm trên ShopeeQuốc tế
chủ nhật 23/05/2021 lúc 05:06 CH
MK8 Extruder Hot End Kit, white wire is temperature thermistor, red wire is heating tube 12V 40W.Perfect replacement accessories/parts for Creality CR-10 CR-10S S4 S5 3D Printer
3 silicone boots and 5pcs 0.4mm brass nozzle for emergency and replacement.It's always practice to have spare parts readily available because failures normally occur when you can least accept them and at a time where there is normally a holiday of sorts to make replacement and/or repair even more inaccessible.
Work with different sizes of MK8 nozzle: 0.2mm 0.3mm 0.4mm 0.5mm 0.6mm 0.8mm 1.0mm nozzle
More stabel temperature. Non-stick silicone sock instead of the cotton isolation is convenient.And most importantly,it offers a huge boost in temperature stability, especially if you use high flow of cooling air around the nozzle to cool the print. Silicone socks will keep the print head stay clean and prevent the filament from sticking to the heater block or spout.
Tip of the nozzle, aluminum heating block, throat pipe (built-in PTFE) MK8 Extruder Hot End Kit, white wire was temperature thermistor, Black wire was heating tube 12V 40W
Installation type: External thread connection
Cable length: 1.2m
Heating Tube: 12V 40W
Operating temperature range: -40~+260 Celsius (-40~+500 Fahrenheit)
Throat length: 52mm
Aluminum block size: approx. 20 x 20 x 10mm
Cable Length:115cm
Connection Method:external line connection
colour: red-based
Material: Aluminum+Stainless Steel+Brass
size: Nozzle size: 0.4mm
Package contents:
1 x Aluminum Block
1 x Heating Tube
1 x M6*30mm Throat Pipe (Built-in PTFE)
1 x Thermistor +Brass Sleeve
1 x 0.4mm Brass Nozzle
3 x Silicone Boots
5 x 0.4mm Brass Nozzle
Only the above package content, other products are not included.
Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.
3 silicone boots and 5pcs 0.4mm brass nozzle for emergency and replacement.It's always practice to have spare parts readily available because failures normally occur when you can least accept them and at a time where there is normally a holiday of sorts to make replacement and/or repair even more inaccessible.
Work with different sizes of MK8 nozzle: 0.2mm 0.3mm 0.4mm 0.5mm 0.6mm 0.8mm 1.0mm nozzle
More stabel temperature. Non-stick silicone sock instead of the cotton isolation is convenient.And most importantly,it offers a huge boost in temperature stability, especially if you use high flow of cooling air around the nozzle to cool the print. Silicone socks will keep the print head stay clean and prevent the filament from sticking to the heater block or spout.
Tip of the nozzle, aluminum heating block, throat pipe (built-in PTFE) MK8 Extruder Hot End Kit, white wire was temperature thermistor, Black wire was heating tube 12V 40W
Installation type: External thread connection
Cable length: 1.2m
Heating Tube: 12V 40W
Operating temperature range: -40~+260 Celsius (-40~+500 Fahrenheit)
Throat length: 52mm
Aluminum block size: approx. 20 x 20 x 10mm
Cable Length:115cm
Connection Method:external line connection
colour: red-based
Material: Aluminum+Stainless Steel+Brass
size: Nozzle size: 0.4mm
Package contents:
1 x Aluminum Block
1 x Heating Tube
1 x M6*30mm Throat Pipe (Built-in PTFE)
1 x Thermistor +Brass Sleeve
1 x 0.4mm Brass Nozzle
3 x Silicone Boots
5 x 0.4mm Brass Nozzle
Only the above package content, other products are not included.
Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.